상품명 | KTRM series 3단 롤러 밀 (Three-roller mill) |
---|---|
공급원 | 한국코프로텍(주) (OEM) |
판매가 | 가격 문의 |
배송비 | ₩5,500 (₩1,000,000 이상 구매 시 무료) |
수량 |
(최소주문수량 1개 이상 / 최대주문수량 0개 이하)
사이즈 가이드수량을 선택해주세요.
위 옵션선택 박스를 선택하시면 아래에 상품이 추가됩니다.
상품명 | 상품수 | 가격 |
---|---|---|
KTRM series 3단 롤러 밀 (Three-roller mill) | 가격 문의 ( 0) | |
총 상품금액(수량) : 0 (0개)
할인가가 적용된 최종 결제예정금액은 주문 시 확인할 수 있습니다. |
주문하시기전에 담당자와 재고 여부 및 배송일정에 대한 상담을 먼저 진행해 주시기 바랍니다. / 대표전화 02-6264-5745
Three-roller mill (쓰리 롤밀) 은 주로 페인트, 잉크, 안료, 플라스틱, 식품 등과 같은 다양한 종류의 페이스트에 사용됩니다.
이 기계는 수평으로 배열된 3개의 롤러 표면과 서로 다른 속도의 마찰을 통해 밀링 및 연삭 효과를 얻습니다.
일반적으로 밀링 재료는 두 번 밀링하여 요구 사항을 충족할 수 있습니다. 그러나 까다로운 재료는 요구 사항을 충족하기 위해 여러 번 밀링해야 합니다.
최종 가공 미세도는 약 3~18μm (미세도 스크레이퍼로 측정)에 이를 수 있습니다. 산-염기 조성으로 원료를 분쇄하거나 롤러 부식을 일으킬 정도로 분쇄하는 것은 적합하지 않습니다.
※ 적용 분야
- 화장품, 식품, CNT, 카본, OLED Paste, Pigment, TiO2, 전지재료
- 전자 세라믹 환경 신소재, 코팅소재, 안료, 전자 재료, 도전성 Paste
- 페인트, 잉크, 파우더, 접착제, 제약, 나노 소재
제품사양
* Machine section
The body adopts castings, which are composed of machine seat and upper cover plate. The left and right sides of the body are equipped with one of each side of the double row centered roller bearing in horizontal direction, and are connected with the upper cover plate. The middle roller bearing seat is bolted with the adjusting screw and the spring on the cover plate to make the front and back movement. The right end of the bearing seat is used to support the slow, medium and fast three rollers. The right end of the roller shaft has a cooling water pipe and water tank, and the left end gear.
* Transmission section:
The lower part of the machine seat is equipped with a motor, which is driven by triangular tape to pass into the fast roller, which is driven to the middle roller by the gear, and the middle roller to the slow roller.
* Roller:
The roller is divided into fast, medium and slow one, all made of cold hard alloy cast iron, the two ends are pressed into the high quality steel shaft head which has been heat treated, the left shaft head is equipped with transmission gear, and the middle through hole of the right shaft head is used as the channel hole for cooling the roller when working. The cold hard layer of the roller is not less than 15mm, its hardness is not less than hardness 70, and the surface is ground by precision.
* Feeding apparatus
The feeding device is composed of copper knife and copper knife support, which is installed at the two ends between the slow roller and the middle roller, the copper knife arc is close to the surface of the slow and middle roller, and the material is not flowing, the copper knife support is fixed on the body with bolts, which is convenient to adjust the edge distance and disassemble and clean, and the copper knife should be adjusted frequently to facilitate the surface of the roller.
* Cooling equipment
In order to eliminate the roller work properly, the heat expansion caused by the friction affects the flat contact surface of the roller, the cooling water pipe is installed at the right shaft head of the roller, and the rubber pipe is installed at the water pipe joint. After heat exchange through the inner wall of the roller, the original hole returns to the water tank and flows into the sewer.
* Discharge device
The discharging plate for discharging is mounted on the body's discharging plate support, the discharging plate is equipped with a blade, and the blade is close to the surface of the fast roller through the adjusting screw of the discharge plate, and the position of the knife edge should be higher than that of the center of the roller, so as to facilitate the smooth scraping of the material attached to the surface of the fast roller after grinding.
* Pressure regulator
Rotate the hand wheel, through the action of the screw and spring, prompt the fast and slow roller to move along the guide rail before and after, to adjust the grinding fineness of the slurry.
- 산간벽지나 도서지방은 별도의 추가금액을 지불하셔야 하는 경우가 있습니다.
고객님께서 주문하신 상품은 입금 확인후 배송해 드립니다. 다만, 상품종류에 따라서 상품의 배송이 다소 지연될 수 있으며,
설치를 필요로 하는 제품의 경우에는 설치과정에 대한 견적과정이 필요합니다
보다 상세한 사항은 유선 연락주시면 성의를 다해서 설명 드리겠습니다.~
02-6264-5745 한국 코프로텍(주)
A/S 문의는 한국코프로텍(주) 02-6264-5745~6 번으로
평일 : 09:00~06:00까지
공휴일 : 휴무